Eaton Fuller Transmission Alignment Troubleshooting
エンジンへの送信の同心の整列
ミスアライメントに起因共通の懸念事項
ダイレクトギアslipout
Drive gear bearing failure
2つの板クラッチの後方ハブから時期尚早入力軸スプライン摩耗
![同心円状のアライメントンメント transmission concentric alignment](https://www.globaltransmissionsupply.com/wp-content/uploads/Concentric-alignment.jpg)
同心円状のアライメント
Concentric alignment means that the engine and transmission must have a common axis. The purpose of this section is to set forth the procedures to use in checking for possible misalignment.
The basic instrument needed for taking readings is a taper pointed dial indicator. The accuracy of readings is essential for correcting alignment problems. Clean all surfaces thoroughly before proceeding.
以下の読み取りを行う場合には, 手でエンジンを回転させます, do not crank the engine with starter. Remove spark plugs on gasoline engines, and release compression on diesel engines.
注意: Before dial indicating engine flywheel or flywheel housing, make sure engine crankshaft does not have excessive end-play. それがない場合, accurate readings cannot be obtained. Place dial indicator finger against the flywheel. Force crankshaft back and forth with pry bar. If end-play movement exceeds maximum as specified by the engine manufacturer, それは修正する必要があります.
摩耗したハウジング
Inspect for worn or fretted pilot on both the transmission clutch housing and the engine flywheel housing. 1/4″ pilot lip of transmission clutch housing can wear into the flywheel housing either by transmission loosening up or after high mileage just from the road and engine vibration.
![伝送ミスアライメントロットment worn or fretted pilot](https://www.globaltransmissionsupply.com/wp-content/uploads/transmission-misalignment.jpg)
Any appreciable amount of wear on either part will cause misalignment and the part should be replaced.
![着用送信ハウジングッションハウジング worn transmission housing](https://www.globaltransmissionsupply.com/wp-content/uploads/worn-transmission-housing.jpg)
摩耗は一般から発見されます 3:00 時まで 8:00 時の位置.
エンジンフライホイールハウジングパイロット
![エンジンフライホイールハウジングパイロット engine flywheel housing pilot](https://www.globaltransmissionsupply.com/wp-content/uploads/engine-flywheel-housing-pilot-400x254.jpg)
![フライホイールハウジング - 全振れングの総振れ flywheel housing total runout](https://www.globaltransmissionsupply.com/wp-content/uploads/flywheel-housing-total-runout.jpg)
Dial indicate the pilot or bore of the engine flywheel housing. Secure dial indicator to engine flywheel with tapered point against housing pilot. 手でフライホイールを回転させます. With chalk or soapstone, mark high and low points of indicator as it is being rotated.
The total runout will be the difference between the highest plus and minus readings. SAE maximum total runout for flywheel housing pilot is .008″ with No.1 and No.2 SAE housings.
フライホイール下穴
フライホイールのパイロットベアリングボアを示すダイヤル. With indicator secured to flywheel housing, move gauge finger to contact pilot bearing bore surface. Turn flywheel and obtain readings. SAE maximum total runout for the pilot bearing is .005″.
![フライホイール・パイロット・ボアパイロットボア flywheel pilot bore](https://www.globaltransmissionsupply.com/wp-content/uploads/flywheel-pilot-bore-e1552489026460.jpg)
トランスミッションクラッチハウジング
The transmission clutch housing face and pilot cannot be checked accurately in the field without special measuring tools. Recommended maximum runout for the transmission clutch housing face and pilot is .003″ with SAE No.1 and No.2 housings.